Do You Have Any Questions?Toll-free (in the US): 1-866-ENDEVCO
Fax: 1-716-684-0987 Contact Endevco We found 33 matches.... Accessories, Rack mount kit for models 133 and 136, holds 3 units
del
133. Gently remove the plastic frame from the Model 133 front panel (store the panel for future
use and for return of the unit to Endevco when required). Hold the Model 133 behind the front
panel mount, (the part with three cut-out rectangular holes), gently insert the Model 133's front IM133-Rev-H2
Model 133 (3-channel) signal conditioner?
Answer
The calibration process is a ""Special"" mode function and is initiated by pressing the < Select Function > push button while simultaneously pressing the < Left > and < Right > EDITS push buttons. Refer to page 1
Model 133, which has selectable IEPE current limits of: 0, 4 and 10 mA. I have an application that requires a longer cable length and a higher bandwidth, which can only be met with an IEPE current level of 18 to 20 mA. Is there a modification that can be made to the Model 133 to accomplish a higher
model 133 conditioner? Is there a definition of the particular error codes, since it is unclear what the error codes mean?
Answer
Yes. See below Table (1.) for the specific error codes and their definitions for both Model 133 and 136.
Viewing the Error Codes
Once the failure LED is on, the model 1
model 133 uses is pC (pico-coulombs) when configured as a charge amplifier, and mV when configured as an ISOTRON (IEPE type) amplifier. The 136 only uses mV. So, for example, when programming the input sensitivity for a charge accelerometer, the 133 will display pC/EU (where EU is engineering unit).
model 133 uses is pC (pico-coulombs) when configured as a charge amplifier, and mV when configured as an ISOTRON (IEPE type) amplifier. The 136 only uses mV. So, for example, when programming the input sensitivity for a charge accelerometer, the 133 will display pC/EU (where EU is engineering unit).
PE / Isotron
®
signal conditioner
Model 133
ENDEVCO www.endevco.com Tel: +1 (866) ENDEVCO [+
s the 133 can be used with both IEPE and charge mode accelerometers. The caveat is that the 133 is a single-ended conditioner, designed for use with single-ended accelerometers. Piezoelectric charge mode accelerometers are available in single-ended and differential output. The 133 does not work with
model 133 is connected to J1. The AC signal is rectified by the diode D1, allowing the positive swing to pass thru while blocking the negative swing. R1 serves as the isolation resistor between the model 133 output and the rectifier circuit. C1 is the filter capacitor and R2 is the discharge path. T
Key features
■
Three-channel PE/IEPE
signal conditioner
■
200 kHz bandwidth
(-3dB Corner)
■
Built-in
model 133 is available. The 133 provides three channels of IEPE signal conditioning in one package, and offers a lot of flexibility in accelerometer choices and output scaling for downstream data acquisition systems. Contact our applications engineers to further discuss your options with IEPE accele
devco 133 and 136 signal conditioners are designed for ease of entry of the accelerometer sensitivity and the desired output specified in millivolts per engineering unit. In cases where very low sensitivity transducers are used, such as high g shock accelerometers the user must either round off the
ENDEVCO www.endevco.com Tel: +1 (866) ENDEVCO [+1 (866) 363-3826]
IM133, Page 1
®
INSTRUCTIO
model 133. While a typical test will probably be a transient event, the square wave is an effective test of rise time and the effects of high frequency bandwidth limitations. (repetition rate).
The Endevco
®
model 751 is a low-cost, lightweight
piezoelectric accelerometer with integral elect
Model 752A12 / A13
ISOTRON
®
accelerometer
Features
• Built-in IEEE P1451.4 TEDS
• Hermetical
The Endevco
®
model 23 is an extremely small
piezoelectric accelerometer. It is designed specifica
Key features
■
Long term stability
■
Hermetically sealed
■
Operational to -452°F
(-269°C)
■
Re
Isotron
®
accelerometer
Model 7253C
ENDEVCO www.endevco.com Tel: +1 (866) ENDEVCO [+1 (866)
Legacy product not for sale
The Endevco
®
brand model 61C is a lightweight piezoelectric
accelerom
Key features
n
Extremely small and light
weight (1 gm)
n
Hermetically sealed,
titanium case
n
Key features
n
Miniature teardrop IEPE
accelerometer
n
IEEE P1451.4 TEDS v0.9
n
Adhesive mount
The Endevco model 7702A-XXXX stud mounted, Isoshear
piezoelectric accelerometer is designed for gen
Isotron
®
accelerometer
Model 35C
ENDEVCO www.endevco.com Tel: +1 (866) ENDEVCO [+1 (866) 36
Key features
n
Hermetically sealed titanium
case
n
Miniature, 0.235 inch cube
n
Lightweight, 0
model 133.
TP 324 Endevco_TP324_REVISED Endevco_TP324_REVISED
DOCUMENT SUBJECT TO U.S. EXPORT CONTROLS. COMPLIANCE APPROVAL REQUIRED PRIOR TO DISTRIBUTIO
mber (133, 136, etc.), firmware revision, address.
2. Send settings for all of the 7 functions programmable through the front panel.
3. Query settings for all of the 7 functions programmable through the front panel.
4. Send calibration constants. The new calibration constant will take effect IM136-Rev-F2
The Endevco
®
model 7251AHT-500M1 is a small
piezoelectric accelerometer with integral electronics
IM6634C
Revision G
Sept 2019
MODEL 6634C
VIBRATION AMPLIFIER
INSTRUCTION
MANUAL
Legacy Produc
11011 133 91 5B
ACK 00000110 006 6 06 1 00110001 061 49 31 \ 01011100 134 92 5C
BEL 00000111 007 7 07 2 00110010 062 50 32 ] 01011101 135 93 5D
BS 00001000 010 8 08 3 00110011 063 51 33 ^ 01011110 136 94 5E
HT 00001001 011 9 09 4 00110100 064 52 34 _ 01011111 137 95 5F
LF 00001010 012 10 0A 5 0 IM6634C-Rev-G
|